AC A/C Compressor w/ Clutch for Sanden SD508 For 1985-1990 Jeep Wrangler CO9537C

Description

A/C Compressor w/ Clutch for Sanden SD508 For 1985-1990 Jeep Wrangler CO9537C
Item Description:
NOTE: Each AC air compressor comes with 100ML of Oil. You dont need to add oil additionally.
Installation
Attention Please:
Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
1. Once the old compressor has been removed, begin by removing the receiver/drier or accumulator, and the expansion valve or orifice tube from the vehicle.
2. Next, flush the condenser and evaporator using a non-oil based A/C flush. The valve must be removed on expansion valve system before the evaporator can be flushed.
· Flush evaporators from inlet to outlet.
3. Install the new receiver drier or accumulator, and new expansion valve or orifice tube.
4. Next, install the new or remanufactured A/C Compressor.
5. Install and tighten the A/C Compressor mounting bolts.
6. Reconnect any electrical connectors to the A/C Compressor.
7. Re-install the refrigerant lines and A/C belt to the A/C Compressor.
8. Reconnect the negative battery cable.
9. Evacuate the A/C system with an A/C servicing machine for at least one hour.
10. Check the system for leaks.
11. If there are no leaks, install the refrigerant charge (Check the A/C system sticker under the hood of the vehicle for the proper amount and type of refrigerant for the system). Then, let the system set for 2 minutes. Doing so will allow the refrigerant to carry the oil and spread more evenly throughout the system.
12. Start the vehicle’s engine and turn on the A/C system.
Note:
To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table.
Please make sure the plug is the same as your old one
Pay attention：
This compressor comes pre-filled with the correct amount of oil.
Thus, there is no need to add any additional oil to your system.
Please add refrigerant to 70-80% without filling up.
There may be noise if the refrigerant is added too much.
Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
Package includes:
1pc  A/C Compressor
More Display:
On Jul-22-20 at 01:39:25 PDT, seller added the following information:
Document
NOTE: Each AC air compressor comes with 100ML of Oil. You dont need to add oil additionally.
Fit For:
2004-2009 for Mazda 3 2.0L
2004-2009 for Mazda 3 2.3L
2006-2010 for Mazda 5 2.3L
2009 for Mazda 3 SPORT 2.0L
Interchange Part Number:
140162C,140639C,50523,C1436,10348310,1010759,1110759,1210759,5511699,7511699
Other Part Number:
25715.5T1NEW, 25715.5T1, 2403-423262, 0610104  KT1347, 11157463, 14-0639C, 10362700, 58463 57463
Installation Method
Attention Please:
Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
1.
Remove compressor:
Remove the A/C belt from the A/C compressor pulley. May involve loosening the belt tensioner (if equipped).
2.receiver drier or accumulator, orifice tube or expansion valve.
3.Disconnect the negative battery cable.
4.Remove the bolt that secures refrigerant lines to the A/C compressor. Inspect A/C lines for any contamination such as metal or excessive dirt inside of them. If you find any contamination the system will need to be cleaned.Flush the condenser and evaporator using NON-OIL BASED A/C flush. On expansion valve systems. The valve must be removed before the  evaporator can be flushed. Flushed condensers from outlet to inlet and evaporators from inlet to outlet.
5.Drain all the oil from the new compressor ,if you compressor has a drain plug you will need to open it up and drain what oil is in there too.
6.Install half oil charge into the compressor and the remainder throughout the system. Turn compressor shaft 8-10 full revolutions to insure front seal and other internal parts are lubricated.
7.Install new receiver drier or accumulator and new orifice tube or expansion valve.
8.Evacuate the A/C system for a minimum of one hour.
9.After evacuation install half the refrigerant charge and let the system set for 1 minute. This will allow the refrigerant to pick up oil and spread more evenly throughout the system.
10.Turn on the A/C system with the engine running and check to see if cold air is now coming out of the air duct.
11.If the A/C system is functioning ,you may find that your electric radiator fan and compressor clutch will be cycling off and on depending on the outside air temperature
Pay attention
This compressor comes pre-filled with the correct amount of oil. There is no need to add any additional oil to your system.
Please add 70-80% refrigerant, do not need to fill up
Noise is generated if too much refrigerant is added
Package Included:
1pc A/C Compressor
（Professional Installer is Highly Recommended ）
WE ACCEPT THESE PAYMENT METHODS
( 10% sales tax will be applied for orders shipped to Washington state by state law )
30 Days easy returns satisfaction guarantee.
Items to be returned must be in original factory condition.
Please enclose a note about item number and order id, your eBay ID and the reason of return.