A/C AC Compressor W/ Clutch For 06-08 Jeep Liberty 07-08 Dodge Nitro 3.7L 255275

Description

eBay
A/C AC Compressor W/ Clutch For 06-08 Jeep Liberty 07-08 Dodge Nitro 3.7L 255275
Item Description:
NOTE: Each AC air compressor comes with 100ML of Oil. You dont need to add oil additionally.
Specification:
Type: A/C Compressor w/ Clutch
Pulley Grooves :6
Pre-filled Oil:100ml
Placement on Vehicle: Front
Fit For:
2006 -2008 Jeep Liberty  V6 3.7L
2007- 2008 Dodge Nitro V6 3.7L
Note:
To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table.
Please make sure the plug is the same as your old one
Installation
Attention Please:
Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
1. Once the old compressor has been removed, begin by removing the receiver/drier or accumulator, and the expansion valve or orifice tube from the vehicle.
2. Next, flush the condenser and evaporator using a non-oil based A/C flush. The valve must be removed on expansion valve system before the evaporator can be flushed.
· Flush evaporators from inlet to outlet.
3. Install the new receiver drier or accumulator, and new expansion valve or orifice tube.
4. Next, install the new or remanufactured A/C Compressor.
5. Install and tighten the A/C Compressor mounting bolts.
6. Reconnect any electrical connectors to the A/C Compressor.
7. Re-install the refrigerant lines and A/C belt to the A/C Compressor.
8. Reconnect the negative battery cable.
9. Evacuate the A/C system with an A/C servicing machine for at least one hour.
10. Check the system for leaks.
11. If there are no leaks, install the refrigerant charge (Check the A/C system sticker under the hood of the vehicle for the proper amount and type of refrigerant for the system). Then, let the system set for 2 minutes. Doing so will allow the refrigerant to carry the oil and spread more evenly throughout the system.
12. Start the vehicle’s engine and turn on the A/C system.
Pay attention：
This compressor comes pre-filled with the correct amount of oil.
Thus, there is no need to add any additional oil to your system.
Please add refrigerant to 70-80% without filling up.
There may be noise if the refrigerant is added too much.
Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.
Package includes:
1pc  A/C Compressor
More Display:
On May-25-21 at 02:50:21 PDT, seller added the following information:
OUR PRODUCT
You are purchasing a Reman compressor with clutch.
SEE COMPATIBILITY
We would appreciate if you could leave us a note with the vehicle specification (Year, Make, Model and Engine) in PayPal when making the payment or in the eBay email system, that way we can be sure that the a/c compressor will fit properly.
THE SYSTEM (COMPRESSOR INSTALLATION)
1 Year Ac Warranty & Agreement
Follow all local, state and federal regulations when servicing mobile A/C systems and read this instruction sheet prior to starting any repairs.
Oil charges and oil types should be closely adhered to for proper A/C performance.
If you are uncertain of
OIL CHARGE OR REFRIGERANT TOTAL SYSTEM  CHARGE
refer to the under hood decal or, OEM service manual.
USE ONLY R-12 OR R-134a REFRIGERANT.
1.
Remove compressor, receiver drier or accumulator, orifice tube or expansion valve.
2.
Flush the condenser and evaporator using
NON-OIL BASED
A/C flush. On expansion valve systems
THE VALVE MUST BE REMOVED
before the evaporator can be flushed.
FLUSHED CONDENSERS FROM OUTLET TO INLET AND EVAPORATORS FROM INLET TO OUTLET.
WARNING:
NEWER STYLE CONDENSER DESIGNS ARE VERY HARD, AND SOMETIME IT WOULD BE IMPOSSIBLE TO DO FLUSH, IN THOSE CASES IT IS SUGGESTED THAT IF THE COMPRESSOR HAS A MAJOR FAILURE THE CONDENSER SHOULD BE REPLACED.
3.
Drain all the oil from the new compressor and dispose of according to local, state and federal laws.
NOTE:
if you compressor has a drain plug you will need to open it up and drain what  oil is in there too,
4.
Install half oil charge into the compressor and the remainder throughout the system. Turn compressor shaft 8-10 full revolutions to insure front seal and other internal parts are lubricated.
5.
Install new receiver drier or accumulator and new orifice tube or expansion valve.
6.
Evacuate the A/C system for a minimum of one hour.
7.
After evacuation install half the refrigerant charge and let the system set for 1 minute. This will allow the refrigerant to pick up oil and spread more evenly throughout the system.
8.
Start engine whit A/C controls on MAX AIR with door and windows open.
9.
Add the remaining charge of refrigerant as called for by the manufacture.
WARRANTY
The warranty over this item consist in a onetime replacement.
Our  warranty does not cover labor, removal, installation, diagnostic and other contingent expenses, just the compressor.  We can offer an advanced warranty replacement. For that, a deposit fee of US 0 would be required, to ensure the return of the original compressor. This deposit would be reimbursed once the original compressor is received back.
In either case, if the compressor  is returned locked up or contaminated , the warranty will be VOIDED. Please, Have your system checked by a professional to guarantee a long and sustainable ac system for years to come.
​​​​​​​
The compressor must be returned with a copy of your purchase order and certified mechanic's invoice.
Thank you and here always to help.  ​​​​​​​
RETURN POLICY
Any warranty after 30 days, customer must pay all shipping charge.
All returns must be pre- approved.
SHIPPING
Free ground shipping to the continental US
Shipment to Alaska, Hawaii, Puerto Rico, Virgin Island, American Samoa and Guam do not qualify for free shipping, shipping is to these locations (USPS Only)
YOUR SATISFACTION IS OUR MAIN GOAL